My Dog’s Too Tall!

by | Nov 21, 2012 | 6 comments

The Veritas Inset vice is a real gem which is why I chose it for our Little John Bench. There’s nothing excessive about it and its qualities lie in its simplicity; simple in design and simple to use. Compared to the wagon vices we’re now more familiar with this one is very compact and so you only get about half the travel however the clamping capacity is surprising large thanks to the two positions for the dog so all in all simple and functional.
For the most part bench dogs go straight through your bench top and they will hold themselves in place with some kind of spring so they can be set at any height you need. In contrast this little vice uses a low dog that locates on top of the moving block so its height is fixed and this is the one draw back that I have found.

The set height of the dog is ½” (12.5mm) and whilst this provides ample support for any thickness you clamp its just too high for anything thinner. For boxes or small drawer sides you would find yourself determined to make it work by packing the work piece up from below and holding it in a balance whilst you try to close the vice around it. That simple use becomes chaotic and out comes the holdfast and batten.

I had a chance to discuss the vice with the chaps from Veritas and it turns out they were aware of the problem and had already taken a look in to some solutions. Offering a lower dog sounds straight forward however due to its small size the aluminium they used wasn’t going to offer enough strength. A prototype had been made up in steel and this works a treat (they sent one over to me and I’ve been trying it out for a little while now). The obvious concerns with the steel are the potential damage it could do to your plane iron if accidentally hit but personally I feel that it works, I’ve always been a plane wielder rather than a sander and I’ve never come in to a time where I’ve hit the dog. A bit of care when your working ought to avoid disasters and it holds very well. Perhaps a quick amendment could be made in the workshop, say a thick piece of suede added to the top for protection? Alternatively you might feel it needs a more permanent soft topper added when its made? We’ll be looking to supply the lower dog with our Little John Workbenches so it would be great to hear your thoughts.

If you’re looking for a low cost wagon vice then the Veritas Inset is the only option that I’m aware of, this is available in our shop and from any Veritas stockist in your country. You can also see the vice being used in this video at the Little John Workbench where I’m making a small box.

 

Related Posts

About Richard Maguire

About Richard Maguire

As a professional hand tool woodworker, Richard found hand tools to be the far more efficient solution for a one man workshop. Richard runs 'The English Woodworker' as an online resource and video education for those looking for a fuss free approach to building fine furniture by hand. Learn More About Richard & The English Woodworker.

6 Comments

  1. Paul Chapman

    Good solution, Richard. I’ve always used metal bench dogs and never yet hit one with a plane. If you add thick leather or other cushioning stuff to the top of the dog, you’ll soon be back to the height problem.

    Reply
    • Richard

      I think you’re bang on right there about adding the extra cushioning. We’ll be cursing that we’ve said we’ve never hit a bench dog before, you know what lifes like!

      Reply
  2. David Gendron

    Could you make one out of hard wood??
    Cheers
    David

    Reply
    • Richard

      Hi David, I think this is a great option and much like most woodworker’s tools we always seem to customise them. This is what I’d do myself actually if I had a one off vice to use although I like to offer something that I know will last a bit longer if I’m supplying to a customer as part of their workbench.
      Thanks, Richard

      Reply
  3. Dominic

    Hi Richard
    Just wondering if you are now supplying a low profile dog with the current Little John’s?
    Thanks, Dominic

    Reply
  4. George

    Can you not top the dog with a slither of copper? Won’t do half as much damage as steel to a plane blade. Also I love your work iv followed you for years! Keep it up 🙂

    Reply

Submit a Comment

Your email address will not be published. Required fields are marked *

Subscribe to Updates:

Related Posts:

Simple Work Holding For Ploughing Grooves [Without a Tail Vice]

Sometimes the biggest challenge of a project can just be getting the wood to stay put while we try to work on it. I suppose it's why it's so easy for us to get lost in the hunt for a perfect workbench design. And drawn in towards all kinds of vice bling and fancy work...

Gluing Up A Workbench Leg [VIDEO]

https://youtu.be/8LBs2h6Vrgc Right then, I finally got round to starting some of these question and answers. This is a bit of an odd ball, but it's something that’s asked a lot. I also see this issue happening a lot… sadly. The problem is delamination. An issue where...

Slightly Over The Top… Top

I was having a good old rummage through the timber store the other day and found an old off cut from a workbench top. It's from one that I made when I was building them for a living. I used to keep these off cuts and put them to the test. Sun exposure, damp, all that...