Cap Iron Fatigue

by | Mar 2, 2016 | 42 comments

Understanding how to use a hand plane properly can make hand planing pretty quick

Since ranting about using the cap iron for dealing with tear out, the question ‘why do you only use it when smoothing?’ comes up a lot.

This question is best answered by me asking you to go and do something.

Go and set your hand plane up to take a shaving with the cap iron nice and close to the edge as we discussed, so it’s actually doing something.

Take a shaving with the grain on a fuss free piece of timber. Begin the cut as normal, but once started take your hand off the front of the plane, only push from behind and give no downwards pressure.

Now a comparison shaving.

Use the same plane but this time with the cap iron right back out of the way (1/8″ or more). Aim for the same depth of cut and of course both times ensure a sharp iron.
Repeat the shaving and once again take off the front hand so the plane is only being pushed forward and not down.

Did you notice the difference? Try it a few times more if you didn’t.

The cap iron pulled back - the best setting to use unless you're doing smoothing planing.

The cap iron pulled back – the best setting to use unless you’re doing smoothing planing.

Here’s what you should find:

Planing with the cap iron set is hard work.

Normally a plane will pull itself down in to a board as we take a shaving, which means we only need to push forwards. Close cap irons remove a lot of this benefit and without applying downwards pressure it will probably skip (something I see people suffering with a lot). This need to add downwards pressure together with the cap iron’s effect on the shaving, adds friction, so all in all it becomes a bloody hard job. This is magnified on thicker shavings.

Like four wheel drive, the cap iron is tremendously useful in the right situation, but turning it on for anything else it’s inefficient. With four wheel drive this will hurt your pocket, while inefficient planing affects you.

To do a good job we have to learn to be efficient. Tear out isn’t the only battle that we have when planing and a bigger one will likely be fatigue. Getting knackered makes us sloppy and that’s a big cause for a rough job.

Don’t confuse that with meaning that it should never be used in anything other than smoothing, but those scenarios are niche and wouldn’t be general run of the mill stuff.

Related Posts

About Richard Maguire

About Richard Maguire

As a professional hand tool woodworker, Richard found hand tools to be the far more efficient solution for a one man workshop. Richard runs 'The English Woodworker' as an online resource and video education for those looking for a fuss free approach to building fine furniture by hand. Learn More About Richard & The English Woodworker.

42 Comments

  1. Paul Chapman

    Excellent post, Richard 🙂

    Reply
    • Richard Maguire

      Cheers Paul 🙂

      Reply
  2. Peter A. McLaughlin

    If you’re correct, (and I have no reason to believe otherwise), this is one of the best pieces of printed advice I’ve seen in quite a while. When I was flattening my oak bench top, the blisters on my left hand were pretty bad. Admittedly, they probably would have blistered in any event, but perhaps not as badly with your advice. I will definitely try it out.
    Peter
    Chicago

    Reply
    • Richard Maguire

      Hi Peter,
      Bugger, a blistered hand, that sounds pretty rough. The only real pressure a plane should put in to your hand (lets say you’re right handed) is across your right hand palm and between your thumb and index finger, where the back of the handle sits. Hopefully this will go someway to help, I’d be really interested in your findings.

      Reply
  3. John Thomas

    Another gem! Thanks for great advise. I have had no formal trainng, so information from experienced people is the way I learn. I will start on a workbench in a few months.

    Reply
    • Richard Maguire

      Cheers John, the sad news is I doubt any of this would be in formal training these days. It’s good to hear you’ll be building your own bench, I hope we’ll get a picture!

      Reply
  4. Jasper

    Yummy, learning by experiment.

    This is a good example of what you wrote in the post of January 15th. “With physics there’s a general rule – you don’t get owt for nowt; there’s always a compromise.”

    Very simple physics in this case. If you want to keep the fibres pushed down and broken forward, the fibres push the plane up and backwards.

    Yep, pushing through fatigue usually means doing the same work again tomorrow.

    Reply
    • Richard Maguire

      Hi Jasper,
      With woodworking, and I think a lot of things in life, it’s about knowing what you need and what you can compromise on. Planes are great examples, they’ve got it all, but you can’t have it all at once!

      Reply
  5. Robert Easton

    Superb! What a rational way to describe, and demonstrate, the mechanics. This kind of teaching is so much better than the “do it because I told you” style of teaching.

    Much appreciated!

    Reply
    • John Taylor

      Have I seen your face Mr Easton on another site, I too like to get another opinion and Richards is very interesting

      Regards John

      Reply
    • Richard Maguire

      Thanks Robert,
      As long as it makes sense… ish, I’m happy!

      Reply
  6. Glen Canaday

    This wasn’t the explanation I was expecting.

    I was expecting, “Because when you’re roughin’ ya don’t bloody need it!”

    But alas, no. Richard surprises again.

    Reply
    • Richard Maguire

      Ha ha, in mark I of the post that was definitely in there… word for word!

      Reply
      • Glen Canaday

        I’ve been reading the blog and watching the videos for a while now, if you couldn’t tell 😉

        But at least this makes me feel better about backing the cap iron off the edge 1/8″ on my metal fore and jointer. That’s not why I did it, though. I just did it because I didn’t care about the finish they left. Roughin’ is roughin’, smoothin’ is finishin’.

        Reply
  7. Ricardo

    Now I understand! Let there be light.
    No setting is the best for every situation.
    Great post, fantastic info.

    Reply
    • Richard Maguire

      Thanks Ricardo, absolutely right. Even just changing species of wood can require slight changes to your tool set up or approach. It doesn’t take much piddling about to get the experience needed to know what best suits your situation.

      Reply
  8. enl

    Very true. One of those things I don’t think about, but have felt the effect of, and never really consciously handled appropriately.

    I’m not sure your explanation would resonate with some of my neighbors as I presently reside in a place where everyone besides me seems to think that four wheel drive is an absolute necessity, and they don’t understand why I don’t get stuck without it yet they do with it.

    Reply
    • Richard Maguire

      Ha, everyone’s got a Case Quadtrac around me… I feel left out in my Panda!

      I think that’s half the battle with woodworking, it’s trying to observe the effects you feel and find a reasoning for them.
      Cheers.

      Reply
      • Jasper

        The low weight of the Panda should help you. With less inertia, you need less grip. I used to drive a Renault Express/Rapid – also lightweight, flimsy by today’s standards – it was quite easy to handle in mud and snow.

        Reply
  9. james

    So are you saying it’s easier planing if i move the cap back?

    Reply
    • Richard Maguire

      Effort wise yes, at the potential cost of the finish. So it’s best out of the way for the bulk, and then utilise it strategically when needed.

      Reply
  10. Paul E Fowler

    Richard,

    Probably the reason I enjoy my single iron woodies so much!

    Paul

    Reply
    • Richard Maguire

      Absolutely Paul!
      It’s always nice having the option, but when you’ve got multiple planes anyway life’s just easier when they’re dedicated.

      Reply
  11. John Taylor

    A very interesting explanation of effect with different settings?? I shall try later with
    interest.

    Thank you Richard……best John

    Reply
    • Richard Maguire

      Thanks John, I do hope you give it a try. Playing around’s always the best way for getting a feel.
      Cheers.

      Reply
  12. John Taylor

    Very interesting explanation of the effect of different settings…….I look forward to trying it out

    Thank you Richard……best John

    Reply
  13. John Taylor

    Tried to comment twice and rejected …..so I will unsubscribe from you site

    Reply
    • Richard Maguire

      Sorry to hear that. If you’re new to commenting or haven’t commented in a while they have to go through a manual approval process – it’s a spam protection. They don’t get rejected, it’s just a slight delay before they come on.

      Reply
  14. Andy Ryalls

    Hi Richard
    Thanks for sharing, love your style. just out of interest do you believe that along with the cap iron the steel that the blade was forged from also makes a difference. The Japanese use many different steels ,matching steels to the tree and grain structure. Originally only using a single iron to plane. All that changed was the mouth size and pitch of the blade.
    PS I’m off to have a play.
    cheers Andy Ryalls

    Reply
    • Richard Maguire

      Hi Andy,
      Very interesting, Japanese woodworking absolutely fascinates me but I kind of feel like a need a spare life to really give it a go!
      To a slight degree I think yes, but I think you’d have to be very knowledgeable of the material properties and practiced with them to really maximise the benefit or get any notable difference.
      Using a brittle iron and swiping hardwood would be a sod when half your cutting edge is snapped off. Saying that I do prefer O1 steel over A2 any day of the week and I do believe I get better results, so I suppose it’s worth some thought.
      Thanks for the comment- nice and thought provoking.

      Reply
  15. Salko Safic

    This is an interesting topic one that landed me in a whole lot of mess and $60 out of pocket for a new cap iron. What I’m about to tell you probably is well known to you already but I have seen the results which astonished me. If you hone a very small secondary degree bevel 45 – 50 deg on the chipbreaker you can plane even against the grain on the most gnarliest wood you can find with zero tear out. I have seen it done and was amazed so I tried it out and I went overboard and shortened the cap iron which resulted in the blade not protruding through the mouth to take any shaving at all. I believe I shortened it by an 8th and this is on the modern chipbreaker. I haven’t tried it again but I would like to.

    Reply
    • Richard Maguire

      Hi Salko,
      I’m sorry to hear your devastation! But you really must bite the bullet and set one up again, I’m not sure if you’ve seen the setting up videos that we did (try the link towards the top of this post) they’re pretty boring, but show a pretty bullet proof way of setting a cap iron for controlling tear out in the way you describe. I’d try next time on something cheap though just in case!

      Reply
  16. Patrick Cyr

    Hi Richard,

    I’m new to the blog after finding you on YouTube. Great videos!

    I only have 1 plane and it’s a smoothing plane. I can adjust the mouth opening on it from almost closed to widely opened.

    What effect dies this have? I played with both settings and didn’t really notice anything.

    Thank you!
    Pat

    Reply
    • Richard Maguire

      Thanks Pat,
      On a good plane that’s got a very well fettled mouth, you can close the mouth up as a fairly reliable way of controlling tear out – it keeps the wood pressed down to itself ahead of the cut. And of course you open the mouth to let thicker shavings through for heavier work. Generally on most planes I find it best if you leave the mouth somewhere in the middle and rely on the cap iron for smoothing, and pull the cap iron back for roughing. We’ve done some videos covering the basics of the cap iron, if you haven’t seen them there’s a link at the top of this post. If your plane hasn’t got a cap iron then just let me know what kind of plane it is.
      That’s a very basic overview.
      Cheers,
      Richard

      Reply
  17. Kees van der Heiden

    Sorry, you are wrong Richard! 😉

    The trick is to set the capiron at an appropriate distance. Too close and planing becomes real hard work. Too far and it isn’t helpfull.

    Especially in the try-plane fase of dressing a board, the capiron is very valuable. Sure, don’t set it too close, but set it close it enough that it prevents disasters, deep tearout that takes ages to remove and makes you go beyond layout lines. On a troublesome board this won’t give you a blemish free surface, that’s the smoothers job, but it sure beats deep tearout.

    A capiron beveled to no more then 45 degrees, set at an appropriate distance from the edge is really not so bad in the aspects you mention. Extra resistance makes you feel that the capiron does its job. If you really want to know what hard work is, try a plane with a high cutting angle.

    Reply
    • Richard Maguire

      Hmm… so ‘wrong’, yet you agree. A cap iron that’s doing something adds resistance.
      Not everyone’s aware of this and it’s an essential mechanic to understand.

      Reply
      • Kees van der Heiden

        I did add a wink.

        I had the feeling you were “throwing out the baby with the bathwater” in your statement that the capiron is only to be used with the smoothing plane and the rest of its use is a niche. While I find the capiron tremendously helpfull in prepping a board, after knocking off the rough and high spots with the jack plane, and starting to make things straight and true with a tryplane.

        And it sure adds resistance, just not enough to be a problem. When the board is easy, you can set the capiron wherever you want and indulge in the ease of working. But when there are knots or swirls or whatever, it is just a good idea to prevent deep tearing early in the game.

        Reply
      • David Weaver

        If it’s adding that much resistance, it’s too close. In about 4 years, I can remember having to set the cap iron on a jack plane twice. Never close other than that – certainly the wood will tell you if that’s necessary.

        Reasonably close, but not that close on a try plane will leave less work with a smoother (which means you can get closer to a mark with a jack) and then wherever it needs to be on a smoother so that it’s engaged on a thicker smoother shaving but not a thin one.

        I do not have significant cap iron resistance with a try plane unless the shaving thickness is a hundredth or so.

        (these are medium hardwood numbers, never checked with softwoods because they don’t usually need much assitance from a cap iron).

        Reply
  18. Rashid

    Hi Richard . . .
    a few blogs ago you said you were going to do a short video on sharpening the plane iron. I have been experimenting with a gradual curve across the whole blade instead of rounding just the edge. I would be very interested in seeing how you sharpen your plane irons 🙂

    p.s. now that your going to be back on the videos, any chance of a follow up to ‘preparing to make a wooden plane?

    Reply
    • Richard Maguire

      Hi Rashid,
      We’re getting there with new video content and once we get going we hope there’ll be a steady stream. The hand plane is now in production.
      Cheers.

      Reply
  19. Kyle

    Great piece if advice mate. Would never have thought the cap iron would have an affect like that. but then again high angle planes are harder to push and the cap iron is sort of acting as increasing the angle when set close to the edge. Then again I may be wrong.

    Love you blog and you videos. Keep them coming

    Cheers Kyle
    Down under

    Reply
  20. Paul E Fowler

    Richard,
    Enjoying your posts, planes have always been a mystery to me.
    Been digging around, discovered that, my Great Grandad’s woodies were single irons.
    My grandads had bee modified wit shims to adjust the mouth on smoothers, as a machinist, I replaced the blades wit thicker ones, to have same effect?

    Paul

    Reply

Submit a Comment

Your email address will not be published. Required fields are marked *

Subscribe to Updates:

Related Posts:

Which Saws Are Best For Ripping Thick Stuff? [Video]

https://youtu.be/N_Io5q8so9E There's a lot of choice when it comes to rip saws. And unfortunately options usually just make things more complicated.So hopefully the video above will help clear up some of the confusion around which saw to reach for or at least give you...

Bench Top Edge Jointing [with Video]

https://youtu.be/12KkjX6IU20 Stuggling With Larger Edge Joints? Watch the full step-by-step video to learn the edge jointing process for tackling large boards by hand. A perfect reference for gluing up a table top. Find it for FREE in our Member Area: Login here. Or...

My Posh Fillister Plane is Just a Roughing Tool

Every now and then I feel like I see something with new eyes. I’m often blow away at the beauty of say the sea, or the sky with a pretty sunrise. It's as though my brain has had a system reset and deleted its memory so I get to see it again like it's for the first...